No. 29, Liansheng South Road, Lianfeng Industrial
Zone, Xiaolan Town, Zhongshan, Guangdong, China
Copyright(c) 2018 Zhongshan Xintai Automation Equipment Co., Ltd . 粤ICP备14015524号 Website:WWW.300.CN ZhongShan
XT-1718-12A-lx-Continuous automatic sand blasting machine
The main parameters
|Equipment dimensions||3900mm long*2000mm wide*3200mm high|
|Equipment working room size||1700mm long * 1800mm wide * 1800mm high|
|dust box||1000mm long *1000mm wide* 2600mm high|
|Dust Removal Fan||4.0KW 380V 50HZ (drawer type waste bucket, pulsed dust removal)|
|Automatic transport mechanism||0.75KW 380V 50HZ[speed adjustable]|
|Auto gun rack||0.37KW 380V 50HZ[speed adjustable]|
|lighting< /td>||18w fluorescent 2|
|number of guns||12 (aluminum alloy strip Boron carbide nozzle)|
|shell< /td>||2.0mm-6mm steel plate welding Made|
|Perspective window||2 frames|
|gate< /td>||open and close 500mm high *450mm wide & times; 2 sheets|
|real for||30 mesh - 280 mesh abrasive : Emery, glass beads.|
|air pressure is greater than||5bar(kg/cm2)|
|maximum load in the working room< /span>||80kg|
|total power||8.5KW or so|
|total weight||about 1.25 tons|
1. The belt is conveyed by the V-belt, and no sand will be accumulated. The belt speed can meet the requirements of the sandblasting process to achieve variable frequency speed regulation;
2, each gun angle can be adjusted freely to achieve automatic frequency conversion swing and fixed point sandblasting, strong flexibility;
3, using advanced upper cyclone separation system configuration, dust separation effect is good, high efficiency of sandblasting;
4, using PLC electrical advanced control system, high degree of automation, good stability, low failure rate;
5. The nozzle adopts special high wear-resistant boron carbide material and has a long service life;
6. Independent bag-type dust removal system, good dust extraction and ventilation;
7. Abrasive recovery uses a combination of spiral conveying and pneumatic recovery, and the recovery is stable. 
Scope of application
Suitable for sandblasting of flat plates, discs, squares, profiles and other shaped workpieces, such as: flat stainless steel sheet, steel sheet, glass plate, stone, non-stick pan, baking pan, toaster, computer case, Function DVD panel, notebook, computer motherboard, electric iron bottom plate, decorative parts, sign badges, communication equipment, aluminum sheets, profiles and other special-shaped pieces.
Fault: a lot of abrasives enter the vacuum bag
Check: Check if the opening of the new vacuum bag separation adjustment belt is too large and the abrasive is too thin.
Solution: 1. Generally, after 8 hours of use, the small mouth can be eliminated; 2. The coarser abrasive is used.
Failure: Abrasives are missing at the workplace
Check: Check the vacuum bag for holes or unclamps.
Solution: 1. Replace the vacuum bag; 2. Re-clamp the vacuum bag.
Fault: the field of view is unclear when sandblasting
Check: 1. Check whether the vacuum bag is blocked; 2. Whether the vacuum bag is aging or not; 3. Whether the abrasive contains too much dust; 4. Whether the recovery pipe is blocked; 5. Is the nozzle hole too large? And whether the compressed air pressure is too high.
Solution: 1. Replace the vacuum bag; 2. Tap the vacuum bag; 3. Replace the abrasive adjustment separator to adjust the belt opening; 4. Check the cause of the blockage of the recovery pipe; 5. The hole diameter cannot be 5.6MM and the recommended pressure is lowered.
Fault: low processing efficiency
Check: 1. Check if the air pressure is too low; 2. Whether the nozzle and the nozzle are too small; 3. Whether there is excessive dust in the abrasive.
Solution: 1. Increase the pressure; 2 Replace the larger nozzle and nozzle; 3 Replace with new abrasive.
Fault: uneven abrasive spray
Check: 1. Check whether the abrasive is less or less; 2. Whether the air pressure is low; 3. Whether the nozzle is blocked; 4. Whether the abrasive is wet; 5. Whether the air gap of the separator regulator is too small.
Solution: 1. Add more abrasive; 2. Increase the pressure; 3. Clear the blockage; 4. Add the dry abrasive; 5. Check the air path to adjust the air gap.
Corresponding parameter set not found, please add it in property template of background
XT-1517-32A-XL catenary automatic sand blasting machine